LBM investigation of a Cu-water nanofluid over various configurations of pipes in the mixed convection flow

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the natural convection mode. However, sedimentation is also very probable at high Ri numbers, which significantly reduces the effectiveness of the nanoparticles. Configurations which produce a natural convection stream similar to the forced convection one as well as the configurations with high spacing and hence, low heat stream interactions, are the best choices for a uniform heat rate from the pipes.     

Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

工业园区混合能源优化配置方法应用与实践

为了充分挖掘多能源之间的互补潜力,使工业园区混合能源系统的配置方式由传统粗放式转变为精确优化配置并降低系统配置方案的保守性,基于粒子群联合CPLEX求解算法对工业园区的系统配置和运行调度方案进行分析优化,并以某生物园区为例进行了实例分析,得到了目标函数下的最优设计方案和运行策略。仿真分析结果表明,优化配置方法的应用能够协调冷热电多种能源的混合利用,提升系统的综合经济性。同时,为工业园区能源供应项目的规划、设计提供参考性支撑,丰富设计手段。     

生物质纤维和改性木质素对聚乳酸结晶性能的影响

采用改性木质素(MZS)作为成核剂,生物质纤维(BF)作为增强剂,通过双螺杆挤出机制备了生物降解的聚乳酸(PLA)/BF/MZS材料。采用差式扫量热仪(DSC)、电子万能试验机和扫描电子显微镜(SEM)分析了BF和MZS对PLA材料性能的影响。结果表明,BF和MZS有效提高了PLA的结晶能力和力学性能。当BF和MZS的含量分别为15%和1%时,PLA材料结晶度提高至67.1%,在50℃/min降温速率下仍具有较高的结晶能力。105℃等温结晶时,15%BF和1%MZS的PLA材料半结晶时间降低至9.0 s,比纯PLA缩短了72.2%。当PLA含有3%BF和1%MZS时,拉伸强度和冲击强度分别为70.1 MPa和7.4 kJ/m^2,比纯PLA分别提高了7.8%和10.4%,根据SEM显示,当BF含量为3%时,在PLA材料中分布较均匀。     

干湿联合冷却塔冷却节水分析软件开发及应用

为实现对干湿联合冷却塔冷却特性、节水特性的综合分析，编制干湿联合冷却塔校核计算流程，基于Visual Studio开发平台，本文开发了干湿联合冷却塔冷却节水特性分析优化软件。通过对某在运干湿联合冷却塔进行冷却节水特性计算，验证了所开发软件计算结果的准确性；在消雾节水计算结果基础上，对标干湿联合消雾冷却塔验收测试规程，生成其成雾频率曲线、耗水量曲线、塔雾指数、冷却特性曲线，综合分析其消雾特性、节水特性及冷却特性，从而确定了干湿联合冷却塔的最佳运行工况。同时运用所开发软件对比分析了某冷却塔设计干段散热面积对其消雾特性、节水特性及冷却特性的耦合影响，并分析了百叶窗开度对干湿联合冷却塔性能的影响，为干湿联合冷却塔的运行优化和设计优化提供了工具性软件支持。     

重力注水过程流动不稳定现象关键影响因素研究

重力驱动注水过程中由于流量较小以及蒸汽的积聚可能导致流动不稳定现象的发生，对核反应堆安全运行具有重要的影响。通过实验研究的方法，搭建了重力注水模拟实验装置，研究了不同蒸汽出口形阻、高位储水箱水位和加热棒初始温度下流动不稳定现象的变化规律。结果表明，重力驱动注水过程流动不稳定现象包含冷却水初次注入阶段、注入水逐出阶段和冷却水再注入阶段等。在一定冷却水初始温度、冷却水入口形阻以及系统压力下，蒸汽排出速度以及实验本体内筒顶部的聚集情况取决于蒸汽出口形阻，减小蒸汽出口形阻可加快蒸汽排放速度，压力峰峰值降低、振荡周期变长，有利于系统稳定；提高高位储水箱水位加快了冷却水注入速率，增加了加热棒被淹没率，降低了流动不稳定现象的发生次数和持续时间；随加热棒初始温度的升高，冷却水流量出现了波动向停滞的转变，流动不稳定现象发生的次数增加且持续时间加长。     

Exergoeconomic performances of the desiccant-evaporative air-conditioning system at different regeneration and reference temperatures

This paper presented the exergoeconomic evaluation of the developed desiccant-evaporative air-conditioning system. The developed system was evaluated based on the steady-state conditions at different regeneration and reference temperatures. The exergoeconomic evaluation method was implemented to the system components and the whole system to evaluate the exergy efficiency, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The regeneration and reference temperatures affected the exergy efficiencies, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The desiccant wheel, heating coil and evaporative cooler had a high cost rate (investment cost, operation and maintenance cost, and exergy destruction cost). The exit air fan, outdoor air fan and evaporative cooler had a high relative cost difference. The exit air fan, outdoor air fan and secondary heat exchanger had a high exergoeconomic factor. Replacement of the desiccant wheel with a higher dehumidification performance could decrease the high cost rate. A higher efficiency evaporative cooler and heating coil were needed. Cheaper air fans (outdoor air fans and exit air fans) were needed.     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。